< Home > < Contact > < Product Book> <Order Form > < Training Seminars >< Distributors> < Dosmatic >
CHLOR*TEST™
------CHLOR*RID-----
Revolutionizing The Industry!
--CHLOR*RID DTS-
---CHLOR*WASH--- Field testing for chlorides by both qualitative and
quantitative methods is common and the threshold for
acceptable levels is dropping, but the cumbersome
----HOLD*BLAST---- methods for testing have remained the same - until now!
CHLOR*TEST - the new way to perform field testing
------TEST KITS------ - revolutionizing the industry!
-----SALT INFO------
CHLOR*TEST - Now available in 50 test bulk
pack!!
CASE HISTORIES
CHLOR*TEST is so complete and easy to use that even the least experienced
inspector can get accurate results. Imagine, a field test that is easy to use, yet more
reliable than any other method of testing.
CHLOR*TEST was developed for ease of use and to prevent outside and cross
contamination. The components are premeasured to ensure accurate results in parts
per million and micrograms per square centimeter. In addition, no temperature
correction is needed for 41 deg. F to 176 deg. F. Field test inspectors around the
world will use this innovative product with confidence on virtually any surface at
Test Results any angle.
Lab Test Parameters For Chloride The CHLOR*TEST uses a unique patented extract solution,
Testing CHLOR*EXTRACT™, to retrieve surface chloride contamination. In the field,
this special extract enhances retrieval rates, thereby increasing accuracy. The
Corrosion Info greater the retrieval rate, the more accurate the test results.
Endorsements When specifications require consistent, safe and reliable testing results for chloride
contamination, use CHLOR*TEST. Each kit contains five (5) individual tests.
Related Sites CHLOR*TEST is designed to be used on vertical, horizontal or overhead surfaces.
CHLOR*TEST is another dependable product developed and manufactured by
CHLOR*RID International, Inc. Since 1994, CHLOR*RID International, Inc. has
earned the reputation of a world leader in soluble salt removal while satisfying the
most aggressive requirements in the protective coatings industry.
CHLOR*TEST is so revolutionary, an inspector will never need:
• Hypodermic needle and syringes
• Deionized water
• Cotton Balls
• Tweezers
• Latex gloves
• A Calculator
• Adhesive tape
• Measuring devices
• Working containers
• Conversion charts
• Reagent chemicals
A Testing Process As Easy As 1 - 2 - 3!
1. Empty the entire contents of the
CHLOR*EXTRACT™ container into the
CHLOR*SLEEVE™. Peel off the protective
backing, pinch the sleeve to expel some of the air
and adhere the sleeve to the surface to be tested.
2. Massage the extract against the surface; then peel the
sleeve off the surface and place it in the perforated hole
in the box lid.
3. Snap the sealed ends off the glass tube, insert it
into the sleeve and down into the extract. In about
two minutes read the color change to identify the
chloride level in both parts per million and micro
grams per centimeter squared, the ratio is 1:1.
Recommend CHLOR*TEST for use on:
• Bridges
• Aircraft
• Mining facilities
• Ships
• Marine structures
• Storage tanks
• Cooling towers
• Pipe lines
• Power plants
• Offshore rigs
• Petrochemical plants
• Pulp and Paper mills
• Steel fabrication
• Electronics
Maximize corrosion protection - Reduce premature coating failure
Test every surface before coating application.
Saatja: Keiu Leopard
Saatmisaeg: 8. detsember 2015. a. 15:37
Adressaat: Karin Jaanhold
Teema: FW: Coatings for maritime usage
Manused: SPE_RUSTGRIP_TECH_ENG.pdf; Chlor-Rid Test Info.pdf; Chlor-rid
Cleaning
brochure.pdf; SPE_MMG_GERMANY_German Life Guard.pdf;
SPE_MMG_TECH_ENG.pdf; SPE_ENAMOGRIP_TECH_ENG.pdf; RUST GRIP-18 LAYERS
LEAD BASED PAINT (03-30-05-VTEC LABS.pdf; SPE_RG_UAE_Mubarak Marine.pdf;
SPE_RG+MMG+RG_ITALY_Saipem.pdf; SPE_RUSTGRIP_USA_US Navy.pdf
See peaks olema teie.
Keiu
From: Airi Kontson
Sent: Tuesday, December 08, 2015 3:34 PM
To: Keiu Leopard <
[email protected]>
Subject: FW: Coatings for maritime usage
Ma arvan see on HNT rida.
Terv
Airi
From: Keiu Leopard
Sent: Tuesday, December 8, 2015 3:12 PM
To: Airi Kontson <
[email protected]>
Subject: FW: Coatings for maritime usage
Kas sa tead sellest midagi?
Keiu
From: Sami Vapalahti [mailto:
[email protected]]
Sent: Tuesday, December 08, 2015 3:00 PM
To: VA_eva <
[email protected]>
Subject: Coatings for maritime usage
To Whome It May Concern,
I participated at Instrutec 2015 fair in Tallinn this year and a
presentative of Estonian maritime organization
was interested in new solutions for coatings of buoys etc. I would like
to bring to knowledge some materials
that are available for these purposes showing high potential for
lifecycle cost reduction. I would appreciate if
this email could be forwarded to a person responsible for
maintenance/purchacing/material selection of used
materials.
Cholr-Rid: Chemical detergent for washing the rusted surface to dissolve
salts. Is very beneficial also for
conventional paints since light blasting is not enough for removing the
salt deposits.
Rust Grip: 1-component polyurethane used by e.g. U.S. Navy as primer for
ships.
https://www.youtube.com/watch?v=Kg-xkZ7W35o
- Can be applied directly on rust
- Can be applied on all surfaces
- Can capsulate lead based paint
- Can capsulate corrosion
- Can capsulate asbestos
Moist Metal Grip: 2-component epoxy for submerged surfaces. Can be
applied on wet surfaces.
Enamo Grip: Surface protection with possibility to tint with different
colours.
I would be very happy to introduce these materials in more detail if
interested. I also have several other
possible coatings that have multiple benefits over current coatings
systems.
Best Regards,
Sami Vapalahti
____________________________
M.Sc. (Metallurgy) Sami Vapalahti
Rodbay Oy
Teollisuuskatu 1
49400 Hamina
+358 50 5930371
[email protected]
http://www.rodbay.fi
CONFIDENTIALITY NOTICE:
This email is intended only for the addressees and may contain
confidential information. If you are not the
intended recipient you are hereby notified that any copying, distribution
or use of the information contained in
this e-mail and its attachments, if any, is not allowed. Any unauthorized
use, copying, review or disclosure is
prohibited. If you have received this e-mail in error, please notify the
sender immediately and delete this e-mail
and any copies of it.
ENAMO GRIP
TECHNICAL SHEET
DESCRIPTION
ENAMO GRIP is a two-part aliphatic polyurethane enamel available in clear and colors. It forms a
uniquely hard and durable coating film, which demonstrates unsurpassed semi-gloss and color
retention, as well as chalk resistance when used in exterior applications. It is resistant to water and
humidity, stains, acids, solvents, and chemicals, as well as having tremendous scuff, mar and impact
resistance. ENAMO GRIP will self-level to an even and smooth finish.
TYPICAL USES
For architectural and maintenance solutions that require the utmost in exterior durability
As a topcoat for RUST GRIP, SUPER THERM and MOIST METAL GRIP
As a floor covering where a tough, long-lasting finish is required
Very good alkali resistance and good acid
Anywhere a solvent-based UV-resistant topcoat is required
APPLICATION METHODS
ENAMO GRIP can be applied to metal, concrete, masonry, wood and other porous surfaces. The
application can be by brush, roller, or airless sprayer. For specific instructions on surface
preparation, mixing and application, please refer to the SPE’s application instructions for ENAMO
GRIP.
NOTE: This product must not be applied on or within 2 inches of chlorinated rubber.
NOTE: Never use mineral spirits to prep surfaces or to thin this product.
MINIMUM SPREAD RATE (thickness)
Porous Surfaces – Apply 1 application of RUST GRIP or ENAMO GRIP @ 200 sq ft/gallon (18
m²/gallon); 8 mils wet / 3.92 mils dry (200 microns wet / 98 dry) to absorb into substrate. Apply 2
additional coats of ENAMO GRIP @ 200 sq ft/gallon; 8 mils wet / 3.92 mils dry, each application.
Non-Porous Surfaces – First apply RUST GRIP as a primer; then apply 1 coat of ENAMO GRIP @ 200
sq ft/gallon (18 m²/gallon); 8 mils wet / 3.92 mils dry (200 microns wet / 98 dry), as an architectural
coating. Apply a second coat of ENAMO GRIP in areas that might have machine or foot traffic,
handrails, or anywhere there is consistent wear on the surface.
Clear Coat Only – Apply 3 applications of ENAMO GRIP @ 200 sq. ft. per gallon (18 m²/gallon)
8 mils wet / 3.0 mils dry (200 microns wet / 78 dry), each application.
ENAMO GRIP
TECHNICAL SHEET
TESTS AND CERTIFICATIONS
USDA Approved
Marine Approval for Salt Water/Maritime Uses:
• US Coast Guard (under renewal)
• ABS (American Bureau of Shipping)
• IMO (International Marine Organization) (under renewal)
Flame Spread (ASTM E84) Class A Fire Rating
Abrasion (ASTM D4060)
Resistance to Wind-Driven Rain (ASTM D 6904)
Water Vapor Transmission (ASTM E 96)
PHYSICAL DATA
Reacted Solids: White - By weight: 64 % / By volume: 49%
Reacted Solids: Clear - By weight: 44% / By volume: 39%
30-60 minutes to tack free at 70°F (21°C)
Overcoat window is three hours or less at 70°F (21°C)
Average Perms: 0.6809
Lead-free / Chromate-free
Cures by chemical reaction
Reacted Weight: White: 11.02 lbs/gallon (1,320 kg/lit); Clear: 8.31 lbs/gallon (0,996 kg/lit)
Aliphatic Polyurethane
Shelf Life: Up to three years (unopened) under appropriate storage conditions (See SDS)
Reactive VOC - White: 2.04 lbs/gal (0,244 kg/lit)
Reactive VOC - Clear: 4.51 lbs/gal (0,540 kg/lit)
Impact Resistance: (Front) 160 psi / (Back) 100 psi
Mix Ratio: 3 parts base to 1 part curing agent by volume
Pot-Life: 4-6 hours at 70°F (21°C), 1 hour at 90°F (32°C). In hot climates (95°F/35°C and
above) pot life can reduce to 1.5 hour. Set pails in ice or ice water to extend pot life.
All colors available with established minimum ordered quantities
Apply between 40°F (4.4°C) and 100°F (38°C)
Maximum Surface Temperature when applying: 150°F (65°C)
Minimum Surface Temperature when applying: 40°F (4.4°C)
Maximum Surface Temperature after curing: 300°F (149°C)
In hot (90°F) temperatures and 85% relative humidity (RH), cut the ENAMO GRIP 4-gallon kit
with one quart of MAK solvent (Methyl n-Amyl Ketone) to slow down the flash off and
skinning of the surface film
ENAMO GRIP
TECHNICAL SHEET
SAFETY PRECAUTIONS
Do not use this product without first taking all appropriate safety measures to prevent property
damage and injuries. These measures may include, without limitation: proper ventilation, use of
proper lamps, wearing of protective clothing and masks, tenting, and proper separation of
application areas. This coating is flammable. Keep away from flame, fire, or other sources of ignition.
For more specific safety procedures, please refer to the ENAMO GRIP Material Safety Data Sheet.
KEEP OUT OF REACH OF CHILDREN.
LIMITATION OF LIABILITY: All recommendations or suggestions relating to the use of the products, whether in technical documentation, or in response to a
specific enquiry, or otherwise, are based on data which to the best of our knowledge is reliable. The products and information are designed for users having
the requisite knowledge and industrial skills, and the end-user has the responsibility to determine the suitability of the product for its intended use. SPE has
no control over either the quality of condition of the substrate, or the many factors affecting the use and application of the product. Therefore, SPE does not
accept any liability arising from loss, injury, or damage resulting from such use or the contents of this data sheet. The information contained in this data sheet
is subject to modification as a result of practical experience and continuous product development. This data sheet replaces and annuls all previous issues
and the user has the responsibility to ensure that this sheet is current prior to using the product.
V-11-21-14 Apr-15
MOIST METAL GRIP
TECHNICAL SHEET
DESCRIPTION
MOIST METAL GRIP is a two-part epoxy coating system that has been specifically designed with
specific additives to promote adhesion when used on metal. MOIST METAL GRIP was developed
to be applied to metal surfaces that cannot be dry enough to use RUST GRIP. It can be used
directly to wet or damp metal surfaces and maintain excellent adhesion to prevent further
surface corrosion. It is a water repelling epoxy for use under water or in areas where constant
splashing or condensation is a problem. It is resistant to chemicals and solvents, and is designed
to be applied directly to concrete, masonry and wood.
TYPICAL USES
As a one-coating system for metal that is moist or in high humidity
As a one-coating system to encapsulate existing rusted surfaces
As a one-coating system to protect metal with condensation issues
As a one-coating system to line tanks
Very good acid and good alkali resistance
As a primer before ENAMO GRIP or LINING KOTE is applied
APPLICATION METHODS
MOIST METAL GRIP can be applied to metal, as well as concrete or masonry substrates. The coating
can be applied by spray, brush, or roller. For specific instructions on surface preparation, mixing and
application, please refer to the SPE Application Instructions for MOIST METAL GRIP.
NOTE: this product must not be applied on or within 2 inches of chlorinated rubber.
NOTE: Never use mineral spirits to prepare surfaces or for thinning.
TEST AND CERTIFICATION
USDA approved
ASTM B117 – Salt spray corrosion test
ASTM D1654 – 450 hour evaluation over black steel
Marine Approvals for salt water/maritime use
US Coast Guard
ABS (American Bureau of Shipping)
IMO (International Marine Organization)
Adhesion: ASTM class 5B – no film pull off
UV and Salt Spray Resistance (ASTM 5894): 10.000 hrs
Potable water and foodstuffs (European)
MOIST METAL GRIP
TECHNICAL SHEET
FIELD TEST HAVE PROVEN:
The coating has outstanding adhesion
The coating is resistant to solvents and chemical splashes
The coating is flexible, yet resistant to impact
MINIMUM SPREAD RATES (mil thickness)
All Surfaces – apply 2-3 applications of MOIST METAL GRIP at 200 sq ft/gallon (18 m²/gallon); 8 mils
wet/4 mils dry (200 microns wet / 100 dry) each coat. This will leave a total thickness of 8-12 dry mils
(200-300 microns dry)
NOTE: Surface and ambient temperatures will determines cure-time. Introduction of heat beneath or
over surface will enhance the cure time.
Inductions Period: 30 minutes at 70°F (21°C)
SPECIAL NOTE: Induction time can span from 5 minutes to one hour according to whether it is
applied to a horizontal or vertical surface, and according to ambient temperatures (see application
instructions)
PHYSICAL DATA
Reacted Solids: By weight 67% / By volume 51%
30-60 MINUTES TO TACK FREE AT 70°F (21°C)
Overcoat window is three hours or less at 70°F (21°C)
Lead and chromate free
Cures by chemical reaction
Reacted Weight: 11.15 lbs. per gallon (1336 gr/lit)
Amine-epoxy
Shelf Life: Up to 3 years (unopened) under appropriate storage condition (see SDS)
Mix Ratio; 4 part base to 1 part curing agent by volume
Reactive VOC - White: 1.32 lbs/gal (158 gr/lit)
Tinting: Can be tinted any color with a minimum of 250 gallons
Resistant to mild concentrations of solvents, chemicals and acids
Maximum Surface Temp when applying; 150°F (65°C)
Minimum Surface Temp when applying; 48°F (8°C)
Maximum Surface Temp after curing; 300°F (149°C)
Failure will occur at a constant temperature equal to or greater than 300°F (149°C)
Consult SPE for intermittent temperatures greater than 300°F (149°C)
Viscosity: 90 seconds, #4 ford cup @ 74°F (23°C)
MOIST METAL GRIP
TECHNICAL SHEET
SAFETY PRECAUTIONS
Do not use this product without first taking all appropriate safety measures to prevent property
damage and injuries. These measures may include, without limitation: proper ventilation, use of
proper lamps, wearing of protective clothing and masks, tenting, and proper separation of
application areas.
This coating is flammable. Keep away from fire, or other sources of ignition.
For more specific safety procedures, please refer to the MOIST METAL GRIP Safety Data Sheet.
KEEP OUT OF REACH OF CHILDREN.
LIMITATION OF LIABILITY: All recommendations or suggestions relating to the use of the products, whether in technical documentation, or in response to a
specific enquiry, or otherwise, are based on data which to the best of our knowledge is reliable. The products and information are designed for users having
the requisite knowledge and industrial skills, and the end-user has the responsibility to determine the suitability of the product for its intended use. SPE has
no control over either the quality of condition of the substrate, or the many factors affecting the use and application of the product. Therefore, SPE does not
accept any liability arising from loss, injury, or damage resulting from such use or the contents of this data sheet. The information contained in this data sheet
is subject to modification as a result of practical experience and continuous product development. This data sheet replaces and annuls all previous issues
and the user has the responsibility to ensure that this sheet is current prior to using the product.
V 3-27-15 Apr-15
RUST GRIP®
TECHNICAL SHEET
DESCRIPTION
RUST GRIP is a tough, one-part, moisture-cure polyurethane coating that absorbs atmospheric
moisture to cure. RUST GRIP is loaded with a metallic pigment for strength and is also resistant to
chemical solvents and acid splash. Upon curing, RUST GRIP provides a protective coating film of
superior adhesion and flexibility, and is resistant to abrasion and impact. RUST GRIP can be used as a
primer or as a one-coating system. It is patented to encapsulate lead-based paints and other toxic
materials, including asbestos. RUST GRIP can be applied over pressure-washed, completely dry flash
rust and firmly bonded commercial paints. In most cases, a white or near-white blasting is not
required. A light to medium surface rust is preferred as the profile.
TYPICAL USES
Good acid and very good alkali resistance.
As a coating to encapsulate rust, lead-based paints and other hazardous materials.
As a protective coating on metal, concrete, wood, etc. to add strength and prevent
deterioration.
As a one-coat system on new or existing bridges, oil platforms, roofs, and other
commercial/industrial surfaces with minimal surface preparation.
As a moisture protective membrane to stop moisture penetration, contaminants, and mold
and mildew.
APPLICATION METHODS
RUST GRIP can be applied to concrete or masonry substrates. The coating can be applied by spray,
brush or roller. For specific instructions on surface preparation, mixing and application, please refer
to the SPE’s application instructions for RUST GRIP (millage may vary due to surface profile).
NOTE: This product must not be applied on or within 2 inches of chlorinated rubber.
NOTE: Never use mineral spirits to prep surfaces or to thin this product.
NOTE: For temperatures 95F/35C and above with less than 20% humidity: RUST GRIP will dry to
touch but will not be completely finished gassing off. If you can move the coating with your fingers,
it is not set hard enough to overcoat; if over coated too soon, bubbles will be caught in the top coat.
NOTE: Zinc rich primers >/= 8.2 kilo of organic zinc per gallon should be removed by sandblast, hand
or power tools prior to application of RUST GRIP. Also, surface should be allowed to develop surface
rust as the profile before applying RUST GRIP.
RUST GRIP®
TECHNICAL SHEET
MINIMUM SPREAD RATE (mil thickness)
Apply RUST GRIP at a minimum thickness of 8 mils wet / 4 mils dry over the highest peaks of the
surface profile. Allow for absorption into the substrate and the filling profile when figuring spread
rate.
NOTE: Surface profile must be factored when estimating the spread rate and amount of product
required. Allow for penetration into the profile and adjust accordingly (i.e. if the profile takes 2 mil
(50 micron) to fill before achieving the 4 mils (100 microns) then you must figure 6 mils (150
microns) dry as the appropriate spread rate).
TEST AND CERTIFICATIONS
Tensile Strength (6,780 psi after 3 weeks)
USDA approved
Factory Mutual approval
E-108-00: Spread of flame on pitched roofs (Class “A” non-combustible)
G85: Prohesion over rusted metal
Marine approvals for salt water/maritime user:
‒ ABS (American Bureau of Shipping)
‒ IMO (International Maritime Organization)
‒ US Coast Guard
Mildew Resistance – excellent (ASTM D3273, 3274)
Chemical Resistance (24 hours/12 reagents)
Flexibility (Mandrel Bend: ASTM D522) – 1/8”
Direct Impact Resistance (ASTM D2794)
Adhesion (ASTM D3359, D4541)
Water Vapor Transmission (ASTM D1653)
Surface Burning Characteristics (E84)
Weathering (2000 hours ) – China
Scrub Resistance (ASTM D2486)
ASTM B117 – 15.000 hours, one coat 6 mils (150 microns) = Perfect score
ASTM E1795 – Encapsulation test group
ASTM D5894 at 10K hrs with perfect 10 score at 6 mils
PHYSICAL DATA
Solids: By weight 62.2% / By volume 51.4%
30-60 MINUTES TO TACK FREE AT 70°F (21°C)
Overcoat window is three hours or less at 70°F (21°C)
Lead and chromate free
Hygroscopic: Cures by absorbing moisture in the air
RUST GRIP®
TECHNICAL SHEET
Net Weight: 9.1 lbs. per gallon
Moisture-cure Polyurethane
Shelf Life: Up to 3 years (unopened) under appropriate storage condition (see SDS)
One component coating; No curing agent needed
VOC Level: 380 grams/liter ; 3.17 gal./lb.
Silver-gray in color; not available in colors
Resistant to most solvents, chemicals and some acids
Maximum Surface Temperature when applying; 150°F (65°C)
Minimum Surface Temperature when applying; 50°F (10°C)
Maximum Surface Temperature after curing; 325°F (163°C)
Failure will occur at a constant temperature equal to or greater than 302°F (150°C); consult
SPE for intermittent temperatures greater than 302°F (150°C)
SAFETY PRECAUTIONS
Do not use this product without first taking all appropriate safety measures to prevent property
damage and injuries. These measures may include, without limitation: proper ventilation, use of
proper lamps, wearing of protective clothing and masks, tenting, and proper separation of
application areas. This coating is flammable. Keep away from fire, or other sources of ignition. For
more specific safety procedures, please refer to the RUST GRIP Safety Data Sheet.
KEEP OUT OF REACH OF CHILDREN.
LIMITATION OF LIABILITY: All recommendations or suggestions relating to the use of the products, whether in technical documentation, or in response to a
specific enquiry, or otherwise, are based on data which to the best of our knowledge is reliable. The products and information are designed for users having
the requisite knowledge and industrial skills, and the end-user has the responsibility to determine the suitability of the product for its intended use. SPE has
no control over either the quality of condition of the substrate, or the many factors affecting the use and application of the product. Therefore, SPE does not
accept any liability arising from loss, injury, or damage resulting from such use or the contents of this data sheet. The information contained in this data sheet
is subject to modification as a result of practical experience and continuous product development. This data sheet replaces and annuls all previous issues
and the user has the responsibility to ensure that this sheet is current prior to using the product.
V 3-6-15 Apr-15
MOIST METAL GRIP
REFERENCE
CUSTOMER: GERMAN LIFE GUARD
PRODUCTS: MOIST METAL GRIP
MARKET: SHIPPING & TRANSPORT
COUNTRY: GERMANY (COURTESY OF SUPERIOR PRODUCTS GERMANY)
PROJECT DESCRIPTION
A rescue vessel of the German Life Guard Association needed to be treated.
COATING SOLUTION
After an thorough preparation with the use of dry-ice blasting and gentle cleaning the hull of the ship was
treated with 2 coats of MOIST METAL GRIP.
RESULTS
Vessel to be treated – preparation cleaning
MOIST METAL GRIP
REFERENCE
Hull after first layer of MOIST METAL GRIP
Rear of the vessel after second layer of MOIST METAL GRIP
MICROPHOTO GRAPH
FOR SUPERIOR PRODUCTS
INTERNATIONAL II, INC.
ON RUST GRIP OVER 18 COATS PAINT
VTEC 100-2115-2
MARCH 30, 2005
1
March 30, 2005
Client: Superior Products International II, Inc.
10835 W. 78th Street
Shawnee, KS 66214
Attention: J.E. Pritchett
Scope:
This report contains microphoto graph pictures taken of the cross
section. Two photos were taken of the cement board with 18 coats of
oil based paint. One photo is the board with the Rust Grip coating and
the other is the board without the Rust Grip coating. Both photos were
taken at 30x zoom.
Preparation of Material:
The Rust Grip coating was applied over 18 coats of an oil based paint
totally encapsulating it. The 18 coats of oil based paint was applied
on a 1/4" thick cement board and was fully cured. The surface was
roughed up with sandpaper before the coating was applied. The Rust
Grip coating was applied in one coats at a thickness of 8-10 mils wet
and allowed to cure for 14 days.
Notice: VTEC Laboratories Inc. will not be liable for any loss or damage resulting from the use of the
data in this report, in excess of the invoice. This report pertains to the sample tested only. Such report
shall not be interpreted to be a warranty, either expressed or implied as to the suitability or fitness of
said sample for such uses or applications, as the party contracting for the report may apply such sample.
2
VTEC #100-2115-2 SUPERIOR PRODUCTS INTERNATIONAL II, INC. MICROPHOTO GRAPH
¼” Cement Board with 18 coats of oil based paint
3
VTEC #100-2115-2 SUPERIOR PRODUCTS INTERNATIONAL II, INC. MICROPHOTO GRAPH
¼” Cement Board with 18 coats of oil based paint and 8-10 wet mils
of Rust Grip
_________________ __________________
Neil Schultz Amirudin Rahim
Executive Director Technical Director
4