Avaldus

EGVV65A-FL-C3-4XR 8-port sector antenna, 2x 694–862, 2x 880–960 and 4x 1695–2690 MHz, 65° HPBW, 4x RET. Low band arrays are diplexed at the element level. All Internal RET actuators are connected in “Cascaded SRET” configuration Uses the 4.3-10 connector which is 40 percent smaller than the 7-16 DIN connector General Specifications Antenna Type Sector Band Multiband Grounding Type RF connector inner conductor and body grounded to reflector and mounting bracket Performance Note Outdoor usage | Wind loading figures are validated by wind tunnel measurements described in white paper WP-112534-EN Radome Material Fiberglass, UV resistant Radiator Material Aluminum | Low loss circuit board Reflector Material Aluminum RF Connector Interface 4.3-10 Female RF Connector Location Bottom RF Connector Quantity, high band 4 RF Connector Quantity, low band 4 RF Connector Quantity, total 8 Remote Electrical Tilt (RET) Information RET Interface 8-pin DIN Female | 8-pin DIN Male RET Interface, quantity 1 female | 1 male Input Voltage 10–30 Vdc Internal RET High band (2) | Low band (2) Power Consumption, idle state, maximum 2W Power Consumption, normal conditions, maximum 13 W Protocol 3GPP/AISG 2.0 (Single RET) Page 1 of 5 ©2021 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks, respectively, of CommScope. All specifications are subject to change without notice. See www.commscope.com for the most current information. Revised: June 8, 2021 EGVV65A-FL-C3-4XR Dimensions Width 301 mm | 11.85 in Depth 180.5 mm | 7.106 in Length 1,416.5 mm | 55.768 in Net Weight, without mounting kit 23.9 kg | 52.69 lb Array Layout Electrical Specifications Impedance 50 ohm Operating Frequency Band 1695 – 2690 MHz | 694 – 862 MHz | 880 – 960 MHz Polarization ±45° 800 W @ 50 °C Page 2 of 5 ©2021 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks, respectively, of CommScope. All specifications are subject to change without notice. See www.commscope.com for the most current information. Revised: June 8, 2021 EGVV65A-FL-C3-4XR Total Input Power, maximum 800 W @ 50 °C Electrical Specifications Frequency Band, MHz 694–862 880–960 1695–1920 1920–2180 2300–2500 2500–2690 Gain, dBi 13.4 13.8 16.8 17.6 18 17.9 Beamwidth, Horizontal, 70 67 64 65 61 60 degrees Beamwidth, Vertical, degrees 16.5 13.8 7.2 6.4 5.5 5.2 Beam Tilt, degrees 2–17 2–17 2–12 2–12 2–12 2–12 USLS (First Lobe), dB 16 16 19 18 17 17 Front-to-Back Ratio at 180°, 27 28 28 31 31 30 dB Isolation, Cross Polarization, 28 28 28 28 28 28 dB Isolation, Inter-band, dB 30 30 30 30 30 30 VSWR | Return loss, dB 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 PIM, 3rd Order, 2 x 20 W, dBc -150 -150 -150 -150 -150 -150 Input Power per Port at 50°C, 200 200 250 250 250 200 maximum, watts Electrical Specifications, BASTA Frequency Band, MHz 694–862 880–960 1695–1920 1920–2180 2300–2500 2500–2690 Gain by all Beam Tilts, 13 13.5 16.3 17.3 17.7 17.6 average, dBi Gain by all Beam Tilts ±0.4 ±0.4 ±0.8 ±0.5 ±0.5 ±0.5 Tolerance, dB Gain by Beam Tilt, average, 2 ° | 12.7 2 ° | 13.1 2 ° | 16.3 2 ° | 17.1 2 ° | 17.7 2 ° | 17.5 dBi 10 ° | 13.1 10 ° | 13.7 7 ° | 16.5 7 ° | 17.4 7 ° | 17.9 7 ° | 17.8 17 ° | 12.9 17 ° | 13.4 12 ° | 16.1 12 ° | 17.0 12 ° | 17.2 12 ° | 17.2 Beamwidth, Horizontal ±2.1 ±3.5 ±5.6 ±6.2 ±5.2 ±4.6 Tolerance, degrees Beamwidth, Vertical ±1.9 ±1 ±0.6 ±0.5 ±0.3 ±0.2 Tolerance, degrees USLS, beampeak to 20° above 19 16 11 14 12 12 beampeak, dB Front-to-Back Total Power at 22 21 21 24 25 22 180° ± 30°, dB CPR at Boresight, dB 22 19 15 17 17 18 CPR at Sector, dB 10 11 9 11 8 9 Page 3 of 5 ©2021 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks, respectively, of CommScope. All specifications are subject to change without notice. See www.commscope.com for the most current information. Revised: June 8, 2021 EGVV65A-FL-C3-4XR Mechanical Specifications Wind Loading at Velocity, frontal 206.0 N @ 150 km/h | 46.3 lbf @ 150 km/h Wind Loading at Velocity, lateral 170.0 N @ 150 km/h | 38.2 lbf @ 150 km/h Wind Loading at Velocity, maximum 397.0 N @ 150 km/h | 89.2 lbf @ 150 km/h Wind Loading at Velocity, rear 209.0 N @ 150 km/h | 47 lbf @ 150 km/h Wind Speed, maximum 241 km/h | 149.75 mph Packaging and Weights Width, packed 429 mm | 16.89 in Depth, packed 329 mm | 12.953 in Length, packed 1672 mm | 65.827 in Weight, gross 35.9 kg | 79.146 lb Regulatory Compliance/Certifications Agency Classification CE Compliant with the relevant CE product directives CHINA-ROHS Above maximum concentration value ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system ROHS Compliant/Exempted Included Products BSAMNT-3 – Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one scissor top bracket set and one bottom bracket set. * Footnotes Performance Note Severe environmental conditions may degrade optimum performance Page 4 of 5 ©2021 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks, respectively, of CommScope. All specifications are subject to change without notice. See www.commscope.com for the most current information. Revised: June 8, 2021 BSAMNT-3 Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one scissor top bracket set and one bottom bracket set. General Specifications Application Outdoor Color Silver Dimensions Compatible Diameter, maximum 115 mm | 4.528 in Compatible Diameter, minimum 60 mm | 2.362 in Material Specifications Material Type Galvanized steel Packaging and Weights Included Brackets | Hardware Packaging quantity 1 Weight, net 6.2 kg | 13.669 lb Regulatory Compliance/Certifications Agency Classification CE Compliant with the relevant CE product directives CHINA-ROHS Below maximum concentration value ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system REACH-SVHC Compliant as per SVHC revision on www.commscope.com/ProductCompliance ROHS Compliant Page 5 of 5 ©2021 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks, respectively, of CommScope. All specifications are subject to change without notice. See www.commscope.com for the most current information. Revised: April 21, 2021 Flexi Multiradio BTS RF Module and Remote Radio Head Description Warnings, cautions or notes related to the product WARNING! Risk of electric shock! Before turning RF power on, RF ports have to be terminated by nominal 50 Ω load (for example, feeder with antenna). However, if these conditions are not met, the plastic caps that are delivered within the unused RF ports should remain in place. The plastic caps isolate RF power from the environment, and thus provide electric shock security in case RF power is accidentally on. Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down. Note: Do not configure the GSM cell power below 30 dB total dynamic range from the max. rated power. It might make the system unstable. 4.13 Flexi RFM 3T6R 900 (FXDB) FXDB (472573A) is introduced by LTE1422/5GC000903. Functional description Table 122: FXDB functional specification Property Value Output power 3x80 W Output power of the cell per TX 5G: 39–49 with 0.1 dB steps Modulation 256 QAM (DL) with 1.3 dB power backoff 64 QAM (UL) 128 © 2021 Nokia.Nokia confidential Flexi Multiradio BTS RF Module and Remote Radio Head Description Property Value number of TXRX 3T6R Outdoor installation Yes Supported technologies GSM, WCDMA, FDD-LTE, 5G (standalone and MSR/concurrent operation) TX frequency range 925–960 MHz RX frequency range 880–915 MHz Supported bandwidths 5G: 5, 10, 15, 20 MHz Instantaneous bandwidth (iBW) 35 MHz Occupied bandwidth (oBW) LTE: • With DIV antennas: 20 MHz • Without DIV antennas: 40 MHz 5G: 35 MHz DL filter bandwidth 35 MHz UL filter bandwidth 35 MHz Note: Do not configure the GSM cell power below 30 dB total dynamic range from the max. rated power. It might make the system unstable. Interfaces © 2021 Nokia.Nokia confidential 129 Flexi Multiradio BTS RF Module and Remote Radio Head Description Figure 28: FXDB interfaces Table 123: FXDB interfaces Interface Label on the Number of Connector Additional hardware interfaces type info Power DC IN 1 Screw- – connector interminal Antenna ANT 6 7/16 – connector RF output RxO 3 QMA – connector Remote RET 1 8-pin circular – Electrical Tilt External Alarm EAC 1 RJ45 – Connection Optical OPT 3 SFP 3 Gbps or 6 interface Gbps 130 © 2021 Nokia.Nokia confidential Flexi Multiradio BTS RF Module and Remote Radio Head Description WARNING! Risk of electric shock! Before turning RF power on, RF ports have to be terminated by nominal 50 Ω load (for example, feeder with antenna). However, if these conditions are not met, the plastic caps that are delivered within the unused RF ports should remain in place. The plastic caps isolate RF power from the environment, and thus provide electric shock security in case RF power is accidentally on. Antenna Line Devices (ALDs) support Table 124: FXDB ALD support ALD support via antenna ports Value AISG ANT1, ANT3, ANT5. RET: AISG 2.0 CWA (for non-AISG installations) Yes Voltage ANT1, ANT3, ANT5: 24 V or 13 V ANT2, ANT4, ANT6: 13 V RET: 24 V Power per port 30 W Functional block diagram © 2021 Nokia.Nokia confidential 131 Flexi Multiradio BTS RF Module and Remote Radio Head Description Figure 29: FXDB functional block diagram Electrical specifications Table 125: FXDB electrical specifications Property Value Nominal supply voltage –48.0 V DC Nominal input voltage range –40.5 V DC to –57.0 V DC Extended input voltage range –36.0 V DC to –40.5 V DC –57.0 V DC to –60.0 V DC Surge protection Class II 5 kA Note: The minimum startup voltage is –40.5 V DC. If the input voltage is below or beyond extended limits, unit might shut down. Power consumption Typical power consumption [W] for 48 V DC input, at 25°C, representative of typical product performance under the same conditions (hardware variant, software version, 132 © 2021 Nokia.Nokia confidential Flexi Multiradio BTS RF Module and Remote Radio Head Description configuration, environment) with +/–10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h. Table 126: FXDB power consumption Mode Configurat Output Power Power Power Power Power Power ion power per consumption consumptio consumptio consumpti consumptio consumptio carrier [W] [W] n [W] n [W] on [W] n [W] n [W] ETSI 202706 ETSI 202706 100% RF Typical as Busy as Max load average load busy hour power load 25% TCH 50% TCH (2% GoS), PRRH, static load PBH RRH, P100% RRH load, 60% load, 60% 60% DTX, 4 static DTX, 4 dB DTX, 4 dB dB PC PC PC GSM 1/1/1 20 460 460 460 460 460 460 2/2/2 20 473 492 586 480 485 490 4/4/4 20 629 731 930 534 561 592 WCDMA 1/1/1 20 331 372 453 2/2/2 20 393 460 606 3/3/3 20 486 588 813 4/4/4 20 543 671 952 LTE 1/1/1 2T2R 20+20 665 753 916 1/1/1 2T2R 40+40 787 932 1223 1/1/1 2T2R 60+60 983 1209 1661 1/1/1 2T2R 80+80 1098 1381 1939 MSR GSM 2/2/2 20 584 637 827 WCDMA 20 1/1/1 Power backoff Table 127: Recommended FXDB power backoff in 256 QAM mode Single carrier [dB] Dual carrier [dB] 1.2 1.3 Installation and mechanical specifications Table 128: FXDB installation and mechanical specifications © 2021 Nokia.Nokia confidential 133 Flexi Multiradio BTS RF Module and Remote Radio Head Description Property Value Installation options • floor/stack installation • pole installation • wall installation • 19'' rack/cabinet IP rating IP65 Related optional items Pole installation • Flexi Mounting Kit for Floor, Wall and Pole (FMFA) • Flexi Pole Kit (FPKA) • Flexi Pole Kit (FPKC) • Flexi Module Casing (EMHx) Floor/Wall installation • Flexi Mounting Kit for Floor, Wall and Pole (FMFA) • Flexi Module Casing (EMHx) Outdoor 19'' rack • Flexi Module Casing (EMHx) Cabinet/indoor 19''' rack • No optional items needed Dimensions and weight Table 129: FXDB dimensions and weight Property Value Dimensions orientation Height Core RFM: 115 mm (4.53 in.) Width Core RFM: 420 mm (16.54 in.) Without front covers: 447 mm (17.6 in.) With front covers: 492 mm (19.37 in.) Depth Core RFM: 400 mm (15.75 in.) Without front covers: 422 mm (16.61 in.) With front covers: 560 mm (22.05 in.) Weight 25 kg (55.1 lb) 134 © 2021 Nokia.Nokia confidential Flexi Multiradio BTS RF Module and Remote Radio Head Description Environmental specifications Table 130: FXDB environmental specifications Property Value Maximum operational outdoor +55°C (131°F) temperature (at constant high ambient temperature maximum output power might be limited) Minimum operational temperature –35°C (–31°F) (including cold start) LTE1422 feature interdependencies There are no interdependencies between this and any other feature. 4.14 Flexi RFM 3T6R 1800 (FXEB) FXEB (472501A) is introduced by LTE1040/5GC000906. Functional description Table 131: FXEB functional specification Property Value Output power 3x80 W Output power of the cell per TX 5G: 39–49 dBm with 0.1 dB steps Modulation Up to 256 QAM (DL) Up to 64 QAM (UL) number of TXRX 3T6R Outdoor installation Yes Supported technologies GSM, FDD-LTE, 5G (standalone and MSR/concurrent operation) © 2021 Nokia.Nokia confidential 135 Flexi Multiradio BTS RF Module and Remote Radio Head Description Property Value TX frequency range 1805–1880 MHz RX frequency range 1710–1785 MHz Instantaneous bandwidth (iBW) 35 MHz in GSM 50 MHz in LTE and 5G Occupied bandwidth (oBW) LTE: • With DIV antennas: 20 MHz • Without DIV antennas: 40 MHz 5G: 40MHz DL filter bandwidth 75 MHz UL filter bandwidth 75 MHz Supported bandwidths 5G: 5, 10, 15, 20 MHz Note: Do not configure the GSM cell power below 30 dB total dynamic range from the max. rated power. It might make the system unstable. Interfaces Figure 30: FXEB interfaces Table 132: FXEB interfaces 136 © 2021 Nokia.Nokia confidential Flexi Multiradio BTS RF Module and Remote Radio Head Description Interface Label on the Number of Connector Additional hardware interfaces type info Power DC IN 1 Screw- – connector interminal Antenna ANT 6 7/16 – connector RF output RxO 3 QMA – connector Remote RET 1 8-pin circular – Electrical Tilt External Alarm EAC 1 RJ45 – Connection Optical OPT 3 SFP 3 Gbps or 6 interface Gbps WARNING! Risk of electric shock! Before turning RF power on, RF ports have to be terminated by nominal 50 Ω load (for example, feeder with antenna). However, if these conditions are not met, the plastic caps that are delivered within the unused RF ports should remain in place. The plastic caps isolate RF power from the environment, and thus provide electric shock security in case RF power is accidentally on. Antenna Line Devices (ALDs) support Table 133: FXEB ALD support ALD support via antenna ports Value AISG ANT1, ANT3, ANT5, RET: AISG 2.0 CWA (for non-AISG installations) Yes Voltage ANT1, ANT3, ANT5: 24 V or 13 V ANT2, ANT4, ANT6: 13 V RET: 24 V Power per port 30 W © 2021 Nokia.Nokia confidential 137 Flexi Multiradio BTS RF Module and Remote Radio Head Description Functional block diagram Figure 31: FXEB functional block diagram Electrical specifications Table 134: FXEB electrical specifications Property Value Nominal supply voltage –48.0 V DC Nominal input voltage range –40.5 V DC to –57.0 V DC Extended input voltage range –36.0 V DC to –40.5 V DC –57.0 V DC to –60.0 V DC Surge protection Class II 5 kA Note: The minimum startup voltage is –40.5 V DC. If the input voltage is below or beyond extended limits, unit might shut down. 138 © 2021 Nokia.Nokia confidential Flexi Multiradio BTS RF Module and Remote Radio Head Description Power consumption Typical power consumption [W] for 48 V DC input, at 25°C, representative of typical product performance under the same conditions (hardware variant, software version, configuration, environment) with +/–10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h. Table 135: FXEB power consumption Mode Configurat Output Power Power Power Power Power Power ion power per consumption consumption consumptio consumptio consumptio consumptio carrier [W] [W] [W] n [W] n [W] n [W] n [W] ETSI 202706 ETSI 202706 100% RF Typical as Busy as Max load average load busy hour power load 25% TCH 50% TCH (2% GoS), PRRH, static load PBH RRH, P100% RRH load, 60% load, 60% 60% DTX, 4 static DTX, 4 dB DTX, 4 dB dB PC PC PC GSM 1/1/1 20 438 438 438 438 438 438 2/2/2 20 454 481 601 452 457 463 4/4/4 20 596 709 957 491 520 554 8/8/8 20 998 1387 1869 LTE 1/1/1 2T2R 20+20 657 728 891 1/1/1 2T2R 40+40 770 907 1226 1/1/1 2T2R 60+60 915 1118 1589 1/1/1 2T2R 80+80 1022 1284 1900 MSR GSM 2/2/2 20 836 937 1206 LTE 1/1/1 20+20 2T2R GSM 4/4/4 20 1002 1198 1592 LTE 1/1/1 20+20 2T2R Power backoff Table 136: Recommended FXEB power backoff in 256 QAM mode Single carrier [dB] Dual carrier [dB] 0.8 1.4 Installation and mechanical specifications Table 137: FXEB installation and mechanical specifications © 2021 Nokia.Nokia confidential 139 Flexi Multiradio BTS RF Module and Remote Radio Head Description Property Value Installation options • floor/stack installation • pole installation • wall installation • 19'' rack/cabinet IP rating IP65 Related optional items Pole installation • Flexi Mounting Kit for Floor, Wall and Pole (FMFA) • Flexi Pole Kit (FPKA) • Flexi Pole Kit (FPKC) • Flexi Module Casing (EMHx) Floor/Wall installation • Flexi Mounting Kit for Floor, Wall and Pole (FMFA) • Flexi Module Casing (EMHx) Outdoor 19'' rack • Flexi Module Casing (EMHx) Cabinet/indoor 19''' rack • No optional items needed Dimensions and weight Table 138: FXEB dimensions and weight Property Value Dimensions orientation Height Core RFM: 115 mm (4.53 in.) Width Core RFM: 420 mm (16.54 in.) Without front covers: 447 mm (17.6 in.) With front covers: 492 mm (19.37 in.) Depth Core RFM: 400 mm (15.75 in.) Without front covers: 422 mm (16.61 in.) With front covers: 560 mm (22.05 in.) Weight 25 kg (55.1 lb) 140 © 2021 Nokia.Nokia confidential Flexi Multiradio BTS RF Module and Remote Radio Head Description Environmental specifications Table 139: FXEB environmental specifications Property Value Maximum operational outdoor +55°C (131°F) temperature (at constant high ambient temperature maximum output power might be limited) Minimum operational temperature –35°C (–31°F) (including cold start) LTE 1040 feature interdependencies There are no interdependencies between this and any other feature. 4.15 Flexi RFM 3-pipe 1800 240 W (FXEE) FXEE is introduced by LTE2471/SR000892:FXEE Flexi RFM 3-Pipe 1800 240 W. Functional description Table 140: FXEE functional specification Property Value Output power 3x80 W MIMO 2TX Outdoor installation Yes Supported technologies (standalone and GSM, FDD-LTE, 5G-ready MSR) TX frequency range 1805-1880 MHz RX frequency range 1710-1785 MHz © 2021 Nokia.Nokia confidential 141 Flexi Multiradio BTS RF Module and Remote Radio Head Description WARNING! Risk of electric shock! Before turning RF power on, RF ports have to be terminated by nominal 50 Ω load (for example, feeder with antenna). However, if these conditions are not met, the plastic caps that are delivered within the unused RF ports should remain in place. The plastic caps isolate RF power from the environment, and thus provide electric shock security in case RF power is accidentally on. Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down. Note: Do not configure the GSM cell power below 30 dB total dynamic range from the max. rated power. It might make the system unstable. 4.20 Flexi RFM 3T6R 2100 (FRGT) FRGT (472810A) is introduced by LTE985/5GC002316. Functional description Table 187: FRGT functional specification Property Value Output power 3x80 W Output power of the cell per TX 5G: 39–49 dBm with 0.1 dB steps Modulation Up to 256 QAM (DL) Up to 64 QAM (UL) Number of TXRX 3T6R Outdoor installation Yes 180 © 2021 Nokia.Nokia confidential Flexi Multiradio BTS RF Module and Remote Radio Head Description Property Value Supported technologies WCDMA, FDD-LTE, 5G (standalone and MSR/concurrent operation) Number of carriers per pipe Up to 4 TX frequency range 2110–2170 MHz RX frequency range 1920–1980 MHz Instantaneous bandwidth (iBW) 60 MHz Occupied bandwidth (oBW) With DIV antennas: 20 MHz Without DIV antennas: 40 MHz DL filter bandwidth 60 MHz UL filter bandwidth 60 MHz Supported bandwidths 5G: 5, 10, 15, 20 MHz Table 188: FRGT output power in RU40 release and onwards DL bandwidth Output power 0–20 MHz 80 W 20–45 MHz 70 W (BTS can be commissioned as 80 W (for example 4x20 W per pipe) and RFM internal power control limits the total power to 70 W when needed.) 45–60 MHz 60 W Interfaces © 2021 Nokia.Nokia confidential 181 Flexi Multiradio BTS RF Module and Remote Radio Head Description Figure 42: FRGT interfaces Table 189: FRGT interfaces Interface Label on the Number of Connector Additional hardware interfaces type info Power DC IN 1 Screw- – connector interminal Antenna ANT 6 7/16 – connector RF output RxO 3 QMA – connector Remote RET 1 8-pin circular – Electrical Tilt External Alarm EAC 1 RJ45 – Connection Optical OPT 3 SFP 3 Gbps or 6 interface Gbps 182 © 2021 Nokia.Nokia confidential Flexi Multiradio BTS RF Module and Remote Radio Head Description WARNING! Risk of electric shock! Before turning RF power on, RF ports have to be terminated by nominal 50 Ω load (for example, feeder with antenna). However, if these conditions are not met, the plastic caps that are delivered within the unused RF ports should remain in place. The plastic caps isolate RF power from the environment, and thus provide electric shock security in case RF power is accidentally on. Antenna Line Devices (ALDs) support Table 190: FRGT ALD support ALD support via antenna ports Value AISG ANT1, ANT3, ANT5, RET: AISG 2.0 CWA (for non-AISG installations) Yes Voltage ANT1, ANT3, ANT5: 24 V or 12 V ANT2, ANT4, ANT6: 12 V RET: 24 V Power per port 30 W Functional block diagram © 2021 Nokia.Nokia confidential 183 Flexi Multiradio BTS RF Module and Remote Radio Head Description Figure 43: FRGT functional block diagram Electrical specifications Table 191: FRGT electrical specifications Property Value Nominal supply voltage –48.0 V DC Nominal input voltage range –40.5 V DC to –57.0 V DC Extended input voltage range –36.0 V DC to –40.5 V DC –57.0 V DC to –60.0 V DC Surge protection Class II 5 kA Note: The minimum startup voltage is –40.5 V DC. If the input voltage is below or beyond extended limits, unit might shut down. Power consumption Typical power consumption [W] for 48 V DC input, at 25°C, representative of typical product performance under the same conditions (hardware variant, software version, 184 © 2021 Nokia.Nokia confidential Flexi Multiradio BTS RF Module and Remote Radio Head Description configuration, environment) with +/–10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h. Table 192: FRGT power consumption Mode Configuratio Output Power Power Power n power per consumptio consumptio consumptio carrier [W] n [W] n [W] n [W] ETSI 202706 ETSI 202706 100% RF average busy hour power load load PRRH, load PBH RRH, P100% RRH static static WCDMA 1/1/1 20 287 316 386 2/2/2 20 356 414 547 3/3/3 20 437 522 729 4/4/4 20 494 608 885 LTE 1/1/1 2T2R 20+20 580 651 796 1/1/1 2T2R 40+40 711 843 1117 1/1/1 2T2R 60+60 818 1010 1427 1/1/1 2T2R 80+80 976 1232 1803 MSR WCDMA 2/2/2 20 719 847 1126 LTE 1/1/1 20+20 2T2R 10MHz WCDMA 2/2/2 20 926 1141 1661 LTE 1/1/1 40+40 2T2R 10MHz Power backoff Table 193: Recommended FRGT power backoff in 256 QAM mode Single carrier [dB] Dual carrier [dB] 0.8 0.8 © 2021 Nokia.Nokia confidential 185 Flexi Multiradio BTS RF Module and Remote Radio Head Description Installation and mechanical specifications Table 194: FRGT installation and mechanical specifications Property Value Installation options • floor/stack installation • pole installation • wall installation • 19'' rack/cabinet IP rating IP65 Related optional items Pole installation • Flexi Mounting Kit for Floor, Wall and Pole (FMFA) • Flexi Pole Kit (FPKA) • Flexi Pole Kit (FPKC) • Flexi Module Casing (EMHx) Floor/Wall installation • Flexi Mounting Kit for Floor, Wall and Pole (FMFA) • Flexi Module Casing (EMHx) Outdoor 19'' rack • Flexi Module Casing (EMHx) Cabinet/indoor 19''' rack • No optional items needed Dimensions and weight Table 195: FRGT dimensions and weight 186 © 2021 Nokia.Nokia confidential Flexi Multiradio BTS RF Module and Remote Radio Head Description Property Value Dimensions orientation Height Core RFM: 115 mm (4.53 in.) Width Core RFM: 420 mm (16.54 in.) Without front covers: 447 mm (17.6 in.) With front covers: 492 mm (19.37 in.) Depth Core RFM: 400 mm (15.75 in.) Without front covers: 422 mm (16.61 in.) With front covers: 560 mm (22.05 in.) Weight 25 kg (55.1 lb) Environmental specifications Table 196: FRGT environmental specifications Property Value Maximum operational outdoor +55°C (131°F) temperature (at constant high ambient temperature maximum output power might be limited) Minimum operational temperature –35°C (–31°F) (including cold start) LTE985 feature interdependencies There are no interdependencies between this and any other feature. © 2021 Nokia.Nokia confidential 187 Flexi Multiradio BTS RF Module and Remote Radio Head Description Warnings, cautions or notes related to the product WARNING! Risk of electric shock! Before turning RF power on, RF ports have to be terminated by nominal 50 Ω load (for example, feeder with antenna). However, if these conditions are not met, the plastic caps that are delivered within the unused RF ports should remain in place. The plastic caps isolate RF power from the environment, and thus provide electric shock security in case RF power is accidentally on. Note: The minimum startup voltage is 40.5 V DC. If the input voltage is below/beyond extended limits, unit might shut down. 5.8 Flexi RFM 6-pipe 800 360 W (FRMF) FRMF is introduced by LTE2547/SR000997:FRMF Flexi RFM 6-pipe 800 360 W . Functional description Table 282: FRMF functional specification Property Value Output power 6x60 W MIMO 2TX Outdoor installation Yes Supported technologies (standalone and FDD-LTE, 5G-ready MSR) TX frequency range 791-821 MHz RX frequency range 832-862 MHz © 2021 Nokia.Nokia confidential 249 Flexi Multiradio BTS RF Module and Remote Radio Head Description Property Value iBW (instantaneous bandwidth) 30 MHz oBW (occupied bandwidth) 30 MHz DL filter bandwidth 30 MHz UL filter bandwidth 30 MHz Interfaces Figure 62: FRMF interfaces Table 283: FRMF interfaces Interface Label on the Number of Connector Additional HW interfaces type info Power DC IN 1 3-pole screw - connector terminal Antenna ANT 6 7/16 - connector RF output RxO 3 QMA - connector Remote RET 1 8-pin circular - Electrical Tilt 250 © 2021 Nokia.Nokia confidential Flexi Multiradio BTS RF Module and Remote Radio Head Description Interface Label on the Number of Connector Additional HW interfaces type info External Alarm EAC 1 MDR36 - Connection Optical OPT 3 SFP 3 Gbps or 6 interface Gbps Antenna Line Devices (ALDs) support Table 284: FRMF ALD support ALD support via antenna ports Value AISG ANT1, ANT3, ANT5, RET: AISG 2.0 Legacy Siemens equipment No CWA (for non-AISG installations) No Voltage ANT1, ANT3, ANT5: 25 V RET: 25 V Power per port 30 W Functional block diagram © 2021 Nokia.Nokia confidential 251 Flexi Multiradio BTS RF Module and Remote Radio Head Description Figure 63: FRMF functional block diagram Electrical specifications Table 285: FRMF electrical specifications Property Value Nominal supply voltage 48.0 V DC Nominal input voltage range -40.5 V DC to -57.0 V DC Extended input voltage range -36.0 V DC to -40.5 V DC -57.0 V DC to -60.0 V DC Surge protection Class II 5kA Power consumption Table 286: FRMF power consumption 252 © 2021 Nokia.Nokia confidential Flexi Multiradio BTS RF Module and Remote Radio Head Description Mode Embedded Configurati Output Estimated power consumption [W] at Power on power per 48VDC input at 25°C. Non-committed Meter carrier [W] estimated values depend on the final support product HW and SW optimization with +/- 10% margin. Average = (6h low hour load, 10h medium hour load and 8h busy hour load) / 24h Power Power Power consumptio consumptio consumptio n n n ETSI ETSI 100% RF 202706 202706 power load average busy hour P100% RRH load PRRH, load PBH RRH, static static LTE Yes 1/1/1 2T2R 20+20 466 533 665 1/1/1 2T2R 40+40 606 733 985 1/1/1 2T2R 60+60 755 942 1326 Table 287: Recommended FRMF power backoff in 256 QAM mode Single carrier [dB] Dual carrier [dB[ 0.7 1.2 Installation and mechanical specifications Table 288: FRMF installation and mechanical specifications Property Value Installation options • floor/stack installation • pole installation • wall installation • 19'' rack/cabinet IP rating IP65 © 2021 Nokia.Nokia confidential 253 Flexi Multiradio BTS RF Module and Remote Radio Head Description Property Value Related optional items Pole installation • Flexi Mounting Kit for Floor, Wall and Pole (FMFA) • Flexi Pole Kit (FPKA) • Flexi Pole Kit (FPKC) • Flexi Module Casing (EMHx) Floor/Wall installation • Flexi Mounting Kit for Floor, Wall and Pole (FMFA) • Flexi Module Casing (EMHx) Outdoor 19'' rack • Flexi Module Casing (EMHx) Cabinet/indoor 19''' rack • No optional items needed Dimensions and weight Table 289: FRMF dimensions and weight Property Value Dimensions orientation Height Core RFM: 115 mm (4.5 in.) Depth Core RFM: 400 mm (15.7 in.) Without front covers: 422 mm (16.6 in.) With front covers: 560 mm (22.1 in.) Width Core RFM: 420 mm (16.5 in.) Without front covers: 447 mm (17.6 in.) With front covers: 492 mm (19.4 in.) Weight 24 kg (52.9 lb) Volume 19.3 l 254 © 2021 Nokia.Nokia confidential Flexi Multiradio BTS RF Module and Remote Radio Head Description Environmental specifications Table 290: FRMF environmental specifications Property Value Maximum operational outdoor +55°C (131°F) temperature (at constant high ambient temperature maximum output power might be limited) Minimum operational temperature -35°C (-31°F) (including cold start) LTE2547 feature interdependencies There are no interdependencies between this and any other feature. LEDs Table 291: FRMF LEDs LED color Description Alarm Red, stable Critical alarm affecting the Fault whole RF module or all antenna carriers Red, blinking Operation degraded Major/critical alarm • Major alarm affecting the whole RF Module • Major alarm affecting the whole RF Module • Major/Critical alarm affecting a module subcomponent or antenna carrier Yellow, stable • Until software download No alarm begins • The carriers are blocked from BTS • There is no connection to any System Module © 2021 Nokia.Nokia confidential 255 Flexi Multiradio BTS RF Module and Remote Radio Head Description LED color Description Alarm Yellow, blinking • Software download in No alarm progress • Configuration in progress: RF resources are being setup, but not yet activated Green, stable • Software configuration is No alarm complete or supervisory: RF resources activated and transmission is possible • Working normally, no alarm on the RF Module Green, blinking Software downloading and No alarm updating Stable Red for less than 5 Switched ON, but the next No alarm seconds and changes to conditions are not reached Stable Yellow yet Stable Red for less than 5 The module is in the No alarm seconds process of resetting Periodic Red and Green Antenna line Alarm faulty/degraded due to external factors (for example, VSWR minor/major values exceeded, Antenna line device faulty/degraded) Blinking Colors (Red, Module highlighting (Flexi No alarm Yellow, and Green), each BTS SM functionality that color stable for 0.5 second can help identifying faulty module) RF Module fan/TX status At least one fan is faulty or LED: Red degraded RF Module fan/TX status All fans are working LED: Green RF Module fan/TX status RF transmission is ON LED: Color set according to fan status, stable RF Module fan/TX status RF transmission is OFF LED: Color set according to fan status, blinking 256 © 2021 Nokia.Nokia confidential Rev: 2.81 Date: 2013-05-21 Outdoor Cabinet – RU 8kW Home FlatPack2-HE 8kW/48V Part no: C20434.000 System Rev: 1.5 Output: Power 6kW / 125.1A Voltage 48 Vdc 34U 32U F1 F2 F3 F4 F5 F6 F7 F11 F12 F13 F14 F15 Modules: Qty F8 F9 F10 F16 F17 30U Rectifiers, FlatPack2-High 3 Max 4 Efficiency, 2000W 28U Blind Panels 1 26U Control Unit, SmartPack EXT 1 24U Battery protection: 22U 20U Type Qty Size 18U LVBD* 1 300A 16U MCCB 3 200A 14U DC distribution: 12U Load breaker type: Siemens (1-63 Amp) 10U Pos Qty Size 8U F1 1 6A 6U F2 – F3 2 20A 4U F4 – F7 4 10A 2U F8 - F10 3 Spare F11 - F12 LVLD* 2 80A F13 - F15 LVLD* 3 32A F16 - F17 LVLD* 2 Spare HxDxW: 1800x823x700mm F18 (service light) 1 2A F19 (smoke detector) 1 2A F20 (Door fan) 1 10A AC distribution F21 (Heater) 1 10A F22 (Leakage protection relay) 1 10A * LVBD = Low Voltage Battery Disconnect ** LVLD = Low Voltage Load Disconnect (150 Amp) Input AC: 3ph 400Vac & AC SPD Parts included: Temp Compensation Charging Battery measurement for 2 x Midpoint Service light Smoke detector Heater 400W/230Vac External alarm board 6analog + 6 digital 1x7U battery shelf 2 x Battery cables 50 sqmm Blue(-) / Black (+) Door with lock, fan and filter Cabinet: Int Dimensions 38U Ext Dimensions 1800 x 823 x 700 mm ( H x D x W ) Weight approx 130 kg excl. rectifier modules www.eltek.com Page 42 of 44